1969 Hot Wheels
US - Chaparral 2G (6256)

US Casting Menu - Misc
1969 History Intro Cars Bodies Chassis Misc HK

Type Click Photo to Enlarge US Chaparral 2G - Rear Hatch
Items in Red show changes from previous version
Prototype
0


Prototype

Part # 6256 0140
  • Revision Letter: None
  • Revision Letter Location: None
  • Tool #: Medium sized "1" at bottom center
  • Top: Engine Window: Wide lined rectangle
  • Hatch Post: None
  • Pair Hatch Mounts: Wide & Short
  • Underside: Front Edge: Flat
  • Underside: Front Center Edge: Flat Circle
  • Underside: Rear Edge to Tail & Sides: Straight & Sharp
  • Rear Tail Recessed Area: Square
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1

  • Car Usage: 1st Prototype
Compare 0 & 1 versions
A


Production

Part # 6256 0140 A
  • Revision Letter: A
  • Revision Letter Location: Large circle at top of hatch
  • Tool #: Large reversed "1" in large circle bottom center
  • Top: Engine Window: Shallow narrow lined rectangle
  • Hatch Post: None
  • Pair Hatch Mounts: Narrow tapered & long
  • Underside: Front Edge: Flat
  • Underside: Front Center Edge: Flat Circle
  • Underside: Rear Edge to Tail area: Slightly Beveled
  • Underside: Side Edge to Sides: Beveled
  • Rear Tail Recessed Area: Tapered
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1

  • Car Usage: Prototype.
    Found on a mid-run production car. Leftover parts bin usage.
Compare 1 & 2 versions
1


Prototype

Part # 6256 0140 A
  • Revision Letter: A
  • Revision Letter Location: Large circle at top of hatch
  • Tool #: >Large reversed "1" in large circle bottom center
  • Top: Engine Window: Shallow narrow lined rectangle
  • Hatch Post: None
  • Pair Hatch Mounts: Narrow tapered & long
  • Underside: Front Edge: Flat
  • Underside: Front Center Edge: Flat Circle
  • Underside: Rear Edge to Tail area: Heavily Beveled
  • Underside: Side Edge to Sides: >Beveled
  • Rear Tail Recessed Area: Tapered
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1

  • Car Usage: Prototype.
    Found on a mid-run production car. Leftover parts bin usage.
Compare 1 & 2 versions
2


Prototype - Bead

Part # 6256 0140
  • Revision Letter: None
  • Revision Letter Location: None
  • Tool #: Large reversed "1" in large circle bottom center
  • Top: Engine Window: Shallow narrow lined rectangle
  • Hatch Post: None
  • Pair Hatch Mounts: Narrow tapered & long
  • Underside: Front Edge: Thick Bead added to entire front edge
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Beveled
  • Rear Tail Recessed Area: Tapered
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1

  • Car Usage: Prototype
Compare 2 & 3 versions
3



Prototype - Bead w/Rev A

Part # 6256 0140 A
  • Revision Letter: A
  • Revision Letter Location: Large circle at top of hatch
  • Tool #: Large reversed "1" in large circle bottom center
  • Top: Engine Window: Narrow lined rectangle
  • Hatch Post: None
  • Pair Hatch Mounts: Narrow tapered & long
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Beveled
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1

  • Car Usage: Prototype.
    Found on a mid-run production car. Leftover parts bin usage.
Compare 3 & A versions
Production - Early Run
  • Once the hatch was decided, three additional tools were created to produce them in volume
A
Tool # 1
Tool # 2 		Stub Post

Part # 6256 0140 B
  • Revision Letter: B
  • Revision Letter Location: End of Stub Post
  • Tool #: Small faint # in right Ejector Pin Circle
  • Top: Engine Window: Narrow lined rectangle
  • Hatch Post: Stub (Very Short)
  • Pair Hatch Mounts: Narrow tapered & long
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1,2,3,4

  • Car Usage: 1
  • Red Enamel

Tool # 3
Tool # 4
Compare A & 4 versions
4



Tool # 2
Prototype - Long Post

Part # 6256 0140 C
  • Revision Letter: C
  • Revision Letter Location: Left Ejector Pin Circle
  • Tool #: Small faint # in right Ejector Pin Circle
  • Hatch Post: Long
  • Pair Hatch Mounts: Thicker Beveled support at top
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1,2,3,4

  • Car Usage: Prototype
  • Zamac Prototype only
Compare 3 & A versions
B
Tool # 1
Tool # 2 		Long Post

Part # 6256 0140 C
  • Revision Letter: C
  • Revision Letter Location: End of Post
  • Tool #: Small # at bottom center
  • Hatch Post: Long (Slighlty longer than proto)
  • Pair Hatch Mounts: Thicker Beveled support at top
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1,2,3,4

  • Car Usage: ???

Tool # 3
Tool # 4
Compare B & C versions
C


Tool # 1
Tool # 2 		Long Post - Double D

Part # 6256 0140 D D
  • Revision Letter: D
  • Revision Letter Location: End of Post & next to Tool #
  • Tool #: Small # at bottom center
  • Hatch Post: Long
  • Pair Hatch Mounts: Additional Beveling around the tops
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Circle with recessed cross strip
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom
  • Tool #s 1,2,3,4

  • Car Usage: ???

  • Tool 1 had its mounting posts re-cut wider & thicker instead of adding extra beveling
  • Later revisions of the other tool would also receive this re-cut

Tool # 3
Tool # 4
Compare C & D versions
Late Run
D
Tool # 1
Tool # 2 		Short Post

Part # 6256 0140 B
  • Revision Letter: B
  • Revision Letter Location: End of Post
  • Tool #: Small # at bottom center
  • Hatch Post: Short
  • Pair Hatch Mounts: Thicker Beveled support at top
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Recessed Area
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom & two at top
  • Tool #s 1,2,3,4

  • Car Usage: ???

Tool # 3
Tool # 4
Compare D & E versions
E
Tool # 1
Tool # 2 		??? Post

Part # 6256 0140
  • Revision Letter: C - not yet seen
  • Revision Letter Location: End of Post
  • Tool #: Small # at bottom center
  • Top: Engine Window: Narrow lined rectangle
  • Hatch Post: Long
  • Pair Hatch Posts: Narrow tapered & long
  • Tool #s ?
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Recessed Area
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom + Two at top

  • Car Usage: ?=Common on over 90% of all cars

Tool # 3
Tool # 4
Compare E & F versions
F
Tool # 1
Tool # 2 		Long Post

Part # 6256 0140
  • Revision Letter: D
  • Revision Letter Location: End of Post
  • Tool #: Small # at bottom center
  • Top: Engine Window: Narrow lined rectangle
  • Hatch Post: Long
  • Pair Hatch Posts: Narrow tapered & long
  • Tool #s ?
  • Underside: Front Edge: Thick Bead
  • Underside: Front Center Edge: Recessed Area
  • Underside: Rear Edge to Tail & Sides: Thicker Beveled
  • Ejector Pin Circles: Two at bottom + Two at top

  • Car Usage: ?=Common on over 90% of all cars

Tool # 3
Tool # 4
Compare F & G versions Still G & H to go LOL
  • Part # Location: # on one Side and Tool # on the otherzzzzzzzzzzzzz
  • Long Hatch Post Hatches are found on over 90% of cars
US Chaparral 2G - Common Hatch Details
  • Originally there was one Hatch, which received changes until it was ready for production, then 3 additional tools were made
  • The Hatch Bolt Pattern is like a fingerprint with each one slightly different.
  • There are several differences but to tell them apart from the outside it's easiest to view the bolt pattern on top of the Hatch
Tool #1 - USA

Protoype & Production 		Tool #2 - USA

Production Only 		Tool #3 - USA

Production Only 		Tool #4 - USA

Production Only
  • info

Type Click Photo to Enlarge US Chaparral 2G - Interior
Items in Red show changes from previous version
Prototype
0

Brown 		McLAREN M6A Interior

Part # 6255 030
  • The McLAREN M6A interior was used for all Chaparral 2Gs
  • Tool #s: 1 - 8

  • Car Usage: Earliest Prototype
Compare 0 & A versions
Production
A

Black 		McLAREN M6A Interior

Part # 6255 030
  • The McLAREN M6A interior was used for all Chaparral 2Gs
  • Tool #s: 1 - 8

  • Car Usage:
    • Black = Common to all production
    • Brown = Hatch Post Cars: Green, Blue, Light Blue


Brown
  • At least 8 tools were used
  • Mattel doubled up and used the existing McLAREN M6A interiors on all US Chaparral 2G cars.

Type Click Photo to Enlarge US Chaparral 2G - Glass
Items in Red show changes from previous version
Production
A
Clear 		US Glass

Part # 6256 017
  • Pair of side post: mate to interior for alignment
  • Tool #s: 1 - 8

  • Car Usage: Prototype and Production
  • Info

Home   |   FAQ   |   Site Map   |   Links   |   Sell-Trade   |     |   Search   |   horizontal rule

Copyright © 2024  www.HWRedlines.com  All rights reserved.
The pictures and descriptions on this site may not be reused without obtaining prior permission.
Hot Wheels are a registered Trademark of Mattel Inc.  This site is not affiliated with Mattel Inc. in any way.